Batt/tine reel
paddles in center of auger
Bottom looks ok.
Rivited sickle sections, sickle drives look ok.
metal crimper
push bar
guide tires
skid shoes
left rear corner welded
Diesel engine, ran one year ago, have not run.
- nice wide fenders
- seat weathered, steering wheel poor, decent gauges
- wide swing draw bar
- 540 PTO
- 2 Hydraulic Couplers
- Inside Rear Wheel Weights
18.4 x 34 B.F. Goodrich Power grip 6 ply tube type, decent tire on widened rim
18.4 x 34 Coop poor tire on standard rim
- has dual loops for Clamp On Duals
- adjustable front axle with 8 bolt hubs & rims
Firestone 4 rib 10.00 x 16 weathered
*****************************************************
I.H. front loader with a 40" bucket, bucket dumps with trip lever, no hydraulic cylinders on bucket.
Loader was made in 2001, attachment brackets are attached to rear axle & inside front frame.
- Runs & drives ok.
- Hydro is 5 years old.
- radiator leaks
- Cab foam is coming off, seat is torn.
- Cylinder bars are hard faced, worn too far on leading edge, probable never turned.
- belt drive return
- unloading tube with bump bar
- long shoe, rear bolt hole brazed
- Loewen chaffer
- late style straw chopper
- Clean grain elevator boot has tape over hole.
- raddle chain has only a couple hundred acres on it
2 - 23.1 X 34 Firestone S.A.T. 23 deg. tubeless 8 ply tires (nice)
2 - 14L x 16.1 SL, Titan 3 rib 8 ply tires; cracks on left tire, right tire has stubble ware, but looks good
- non adjustable rear axle with 8 bolt hubs
- Hydraulic valve area is oily.
-Pipe type pick-up reel with poly fingers & Anti-wrap ends
-Weighted arm wobble box looks ok.
-A.M. flex snouts, metal with divider rods
-bolt on sickle sections with aggressive serration
-Flex stainless looks good.
-Metal bottom is patched.
-Spiral fingered auger looks ok.
-warning lights; field lights
-hydraulic reel lift & drive
-hydraulic Fore & Aft
-depth gauge
-Reel gear shield & left end shield are gone.
-Right end stainless jumped over cutter bar plate.
4290 hours showing
LP Runs & drives - Head gasket leaks
7th gear out on syncro transmission
2 SCVs
540 PTO
no drawbar
3 point with top link
square top fenders
decent seat
Hood looks good & side panels are in place.
heavy inside rear wheel weights
adjustable front axle with 10.00 x 16 tires on 6 bolt rims
18.4 x 34 Firestone S.A.T. 23 deg. 6 ply tube type tires (decent)
*************G B Loader 800 SRS / s/n 8443 / 800 work master********
hydraulics operate from tractor SCVs
arms reinforced on both sides towards the front
White paint is poor.
Loader appears to be in decent condition.
***NO attachments or Bucket***
- plastic teeth, metal tear drop pickup reel with Anti-wrap ends
- small auger dent
- bolt on sickle sections
- short snout
- wobble box
- left hand drive shaft, outer U-joint, apart but in the header
- end shields
- hydraulic reel lift & drive
- hydraulic Fore & Aft
- Bottom looks ok.
- crimper s/n E00030X640483 (steel crimper rolls)
- Gear box looks ok.
- E59258 wobble box
- Left end of head is welded some.
- end shields, poor
- Reel looks ok, some welds on batts, tine & batt style.
- Push bar is bent.
- bolt on sickle sections
- auger dents
- skid shoes, some poly is worn
-Left hand snout is missing, right hand snout is ok.
-Two guards are missing, 2 or 3 guards are broken.
-Auger & bottom look ok.
-Sickle has bolt on sections.
-Wobble box is probable ok.
-Pickup reel is decent, wood with steel teeth & saver tile covers.
-shields missing
-hydraulic reel lift & drive
-diesel engine
-6 speed transmission with Hydra-Power drive, direct drive
-18.4 x 30 tires on cast wheels
-cast rear wheel weights
-solid front axle
-7.50 x 18 3 rib tires on 6 bolt wheels
-Right hand brake was stuck so cover is off (we have cover)
-wide swing drawbar
-540 PTO
-one SCV
-Hydraulic lines are hooked into rear housing to run hydraulic valve for front loader.
-nice fenders
-bad seat
-tool box
-2475 hours showing
-cast grill
-tin work ok but faded
-Tractor has front loader - Dual brand
Open style wobble box, seems ok
Bolt on sickle sections, head bolt seems loose.
Batt reel with Anti-wrap ends
Hydraulic fore & aft
Left end shield is missing, right end is ok.
Bottom is ok also has Rock guards.
Auger needs some finger guides.
Flex shaft for left drive shaft drives auger & wobble box.
Paint on back is peeling.
-black batt reel with Anti-wrap ends
-Auger is decent but is missing a few fingers (spiral pattern).
-small holes in center of bottom
-bolt on sickle sections, no sickle head
-end shields
-rock guards
-weighted wobble box arm
-Wobble box turns, but is very tight.
-Snouts are straight.
-divider rods
-batt reel with Anti-wrap ends
-hydraulic reel drive & lift
-riveted sickle sections, looks ok
-auger, good
-holes in bottom, patched
-no rock guards
-very slight play in wobble box
-decent tin work & snouts
-decent gears & under side
-belts weathered, usable
-right hood, dented
-right shield, missing; left shield, missing
-skid shoes with almost new poly skids
-gears look good
-no stalk stompers
-regular length drive shafts
-auger looks good
-small hole in bottom right seam of center
-depth gauge
- It was serial numbered as R75, was used as R76, S77, and S88.
- It has a 30 inch rotor for 7 & 8 SRS. It's cage is made for S88 gear box.
- shoe is experimental
- Engine - "CORE" AGCO SISU power 84 AWI (Finland)
-pickup reel, decent
-wobble box seems ok, mounting bolts, seems loose
-good cutter bar with riveted sickle
-good auger with bolt on feed flap
-good bottom
-no rock guards
-heavy iron on bottom of back frame
-L.H, drive shaft support redone
-good paint
-hydraulic reel drive
-hydraulic reel lift
Sat for a while; should run
Cummins V8 diesel engine
4 - 23.1 x 30 Goodyear Dyna Torque II 8 ply tube type tires Rims have some rust.
2 - SCVs
wide swing drawbar
no PTO nor 3 point
Was last used about 2 years ago, it was ok when parked.
Snouts look decent, some need new poly points, one is cracked.
corn ear savers
-Right fender is bent on top.
-Chains, snap rolls, plates all look ok.
-Auger has center flaps.
-Bottom looks ok.
-Drive shafts look ok.
-Paint is decent.
-no safety lights
-540 PTO shaft
-Bale - Trak monitor
-jack
-decent pick up unit with guide wheels
-twine arms
-good belts
-31 x 13.50 x 15 tires on 6 bolt rims
-Good Samson 10 ply & fair only Armstrong 8 ply
-decent side doors
-Rollers look ok, some rubber off.
-Hydraulic cylinders look ok.
-Tail gate is rewelded & has small cracks.
-40 hours on engine over haul
-Cab door and window are off, we have both, hinge broke.
-Seat is bad, cab is rough.
-tool box
-6539 hours showing
-2 SCVs
-wide swing drawbar
-no PTO, no 3 point
-big inside rear wheel weights
-cast axle mount duals - 18.4" x 38" rims & tires
-18.4 x 38 Harvest King, inside tires nice; outside tires poor
-adjustable front axle
-14 L x 16.1 SL BKT PRO RIB 12 ply 4 rib front tires on 8 bolt rims
-Left hand side louver is dented.
-Hood & grill are ok.
-has tree sheer attachment on a loader
-seat turned around to use backwards
-spray attachment on front
-gas engine
-13.6 x 28 P.A. rims
-adjustable front axle
-6.50 x 15 front tires on 5 bolt rims
-540 PTO
-drawbar front & back
-hydraulic & power steering appear to run from front mounted pump
-hitch for rear arms
-Gleaner 830A LM Corn Head
-Black
-snouts, off, look ok
-snap rolls worn
-chain & sprockets, fair
-auger, ok
-bottom, hole on left side
-right fender, small crack on top, a gash on the inside front and a dent in back
-left fender, small dent in back
-chain covers, fair
- all metal batt reel, large pipe,
- wobble box, ok,
- riveted sickle, cutter bar looks good,
- black auger, large fingers, needs guides,
- drive shafts look ok,
- shields,
- self contained hydraulics on Header,
- hydraulic reel lift & drive,
- hoop dividers,
- rock guards,
- bottom looks good,
- back rail bows down on left end,
- green stripe
- Damage to throat area,
- Batt reel good all steel,
- bottom good,
- auger good - grey,
- bolt on sickle sections - ok,
- good wobble box,
- RH weights,
- Hyd. run from combine
