All Equipment For Sale

200 Series 24 FT Rigid Header

700 30FT Header AGCO LTM

1010 25FT Rigid Header

LH drive end shields missing open style wobble box Auger looks good. late style pickup reel, good sickle sections worn guards ok

1020 30 FT Flex Header

dual drive both end shields in place oil bath wobble box sickle, good guards, good full finger auger, center flighting extensions pickup reel, ok, some bushing pipes repaired bottom ok combine hookup hoses missing

1020 25FT Flex Header

LH drive open style wobble box end shields missing manual fore & aft auger, ok early style pickup reel, some sections bent bottom, decent sickle, decent guards, decent

1032 - Western Special - CK

Diesel engine, ran one year ago, have not run. - nice wide fenders - seat weathered, steering wheel poor, decent gauges - wide swing draw bar - 540 PTO - 2 Hydraulic Couplers - Inside Rear Wheel Weights 18.4 x 34 B.F. Goodrich Power grip 6 ply tube type, decent tire on widened rim 18.4 x 34 Coop poor tire on standard rim - has dual loops for Clamp On Duals - adjustable front axle with 8 bolt hubs & rims Firestone 4 rib 10.00 x 16 weathered ***************************************************** I.H. front loader with a 40" bucket, bucket dumps with trip lever, no hydraulic cylinders on bucket. Loader was made in 2001, attachment brackets are attached to rear axle & inside front frame.

8000 Flex 30 FT AGCO header LTM

-Hydraulic hoses that connect to the combine are missing. -Challenger yellow shield -safety lights - wires disconnected -Black pipe pick up reel with poly teeth and solid Anti-wrap ends -hydraulic reel drive & lift -electric hydraulic Fore & aft -long flex divider snouts -open style wobble box -bolt on sickle sections -tall flighting, gray auger, big fingers & guides -Bottom looks ok. -Front stainless looks ok. -1000 spline PTO, shaft drive left side -poly skids on front flex plates -decent paint -Back rail is straight. -wide throat hook up options -Sat in shed for years and not used.

Draper Dyna Flex

-Back lower frame was bent when header impacted the ground. -Sickle heads are popped out of the wobble box connections. -Most shields appear to be in place, except 2 on the back. -Two 1000 spline PTO drive shafts -back foot stands -Single point hydraulics -warning lights -bolt on sickle sections -Raptor WCCD Belting Inc, draper belts look ok. -Left end snout has some damage. -black pick up reel, round pipe & poly teeth -electric hydraulic Fore & aft -pressure gauge & pointer -Lateral tilt adapter Assy

1010 25FT Rigid Header

- metal batt reel - hydraulic reel lift & drive - hydraulic Fore & Aft - bolt on sickle sections - Auger needs finger guides & one finger, also has flighting extensions, - Bottom looks ok. - rock guards - left PTO drive shaft - shields - open style wobble box - crop dividers, right hand one home made

300 20 FT Flex Header Deutz-Allis

Hydraulics is run from combine hydraulic system. ********************** Pickup Reel - tear drop metal batt reel with poly teeth cut short w/ good rings & open sided Anti-wrap ends - hydraulic reel lift & drive - long flex snouts - wobble box drive - bolt on sickle sections - large finger auger - Bottom looks ok. - paint faded - shields probably all there - Hydraulics runs from combine system

971 30FT Rigid Header

-all metal tear drop style pickup reel, poly fingers -hydraulic reel drive & lift -Wobble box drives from both sides. -good bolt on sickle sections, extra left hand sickle -good looking guards -Auger looks good. -Bottom looks good. -Most shields are in place. -PTO drives on both sides -rock guards -reel drive, hoses poor -crop dividers -good paint

300 24FT Rigid Header Deutz-Allis

Hydraulics is run from combine hydraulic system. ********************** - Batt reel, all metal with Anti-wrap ends, - Auger is decent, flighting extensions in center, needs finger guides., - rock guards, - single drive shaft, - open wobble box, - bolt on sickle sections, - Head bolt is a little loose, should tighten ok., - Cutter bar looks decent., - Bottom looks ok., - Hydraulic reel lift & drive, - Left crop divider rod is gone, right one is in place., - Left end shield is missing., - Left idler pulleys & belt look good., - Back rail is ok., - Black paint is faded.

300 20FT Flex Header Deutz-Allis

Hydraulics is run from combine hydraulic system. ************** - Header was on R62, - pickup reel, - poly skids, - flex snouts, - single drive shaft, - hydraulic reel lift & drive, - open wobble box, - equipped with Gebr. Schumacher, easy cut cutter bar system S.I. Distributing, St. Marys, Ohio, - bolt on sickle sections, - Flex bar, pan & bottom look ok., - Big Finger auger, - Shields are in place, green strip.

N Srs 3 24FT Rigid Header

Black pickup reel with wood boards, decent reel Rivited sickle sections. Good wobble box, looks like it was recently replaced. Bottom patched and some holes on left side Auger looks ok. Rock guards hydraulic reel drive & lift self contained hydraulics on right hand side Black paint is poor.

900 Series 30FT Rigid Header

-Large pipe black, batt reel -Wobble box arm is broken & loose. -bolt on sickle sections -Guards & cutter bar look good. -L.H. crop divider, snouts welded or dinged some -good bottom -Some of the rock guards are worn & dented in. -Auger needs some finger guides, random style. -end shields -hydraulic reel lift, drive & fore & aft -Drive shaft look good.

1015 13FT Pick-up Header

Bottom looks ok, small dings. Auger looks ok, small dings. Left hand PTO shaft drives the auger. Hydraulic system drives the pick up unit. Rake up Precision Metal Fabrication, LTD - Rosetown, Saskatchewan - s/n 125-9114 - Draper belts have alluminum batts with rubber & poly teeth. - One alluminum batt is broken. Batts are run by a drive box. - Draper is run by a hydraulic motor, held with shock absorbers.

200 Series 24FT Rigid Header

-Batt reel with Anti-wrap on one end -wobble box, ok -bolt on sickle sections, ball joint loose -spiral finger auger -bottom patched -Left end shield is gone. -rock guards -Left hand end pulley is almost new.

200 Series 24FT Rigid Header

-1 snout missing -batt reel with Anti-wrap ends -bolt on sickle sections -good wobble box -spiral finger auger -bottom patched -end shields -hydraulic reel drive & lift -rock guards -decent paint

16FT Swather Header

-tine & batt type reel, 1 batt is off -bolt on sickle sections -Auger has some dents, center flap, looks usable -Bottom looks decent. -double sickle drives -skid shoes -center link -warning lights broken off. -Left end is rusty. -Left back rail drive shaft support is welded.

9600 JD to MacDon header

Plate only no Hydraulics

1010 30FT Rigid Header

Batt reel with Anti-wrap ends, batts are bent & welded. rock guards hydraulic reel drive & lift Hydraulic Fore & Aft Wobble box feels good. bolt on sickle sections, look good Bottom looks ok. Auger looks ok. PTO drive shafts, both sides Right side has shields, left side shield is missing.

LM 15FT Flex Header

-Pickup reel has wood boards, metal teeth, drain pipes over wood rings & rollers (look ok), Anti-wrap ends. -Black open style wobble box -tiger teeth sickle and guards, bolt on sections -Flex bar & snouts, left snout is welded. -Variable speed reel -Hydraulic reel lift; master cylinder is a little oily. -Black auger has small fingers & neoprene guides. -Bottom is patched, but usable. -Depth control gauge looks disconnected. -Hydraulic hoses to combine are missing. -drive coupler

9030 Bi-Directional Frame

900 Series 30FT Rigid Header

-Batt reel with Anti-wrap ends, batts are wavey. -hydraulic reel drive & lift -good wobble box on cast stand -bolt on sickle sections -left snout bent a little -Bottom has center patch -Left shield is missing. Tear drop shield for reel drive is missing. -Auger is good, nice center repair kit, spiral finger pattern -rock guards

300 24FT Rigid Header AGCO

Hydraulics is run from combine hydraulic system. ********************** - black metal tear drop pickup reel with plastic teeth, - bolt on sickle sections, - Cutter bar looks ok., - open wobble box, - hydraulic reel lift, - Bottom has one large hole left of center, otherwise it looks ok., - Left hand end shield is missing., - one weld crack on lift side on back rail, - Back shaft is ok., - 3 right side weights, - crop dividers, - large finger auger

Swather Platform

-(178 W) 14' Head is from JD 830. -Steel conditioners look good. -wobble box -bolt on sickle sections -Yellow batt / pickup reel looks ok. -Push bar is straight. -small dents in auger, center flaps -Bottom is probable ok. -weld at crimper attach bracket -skid shoes

200 Series 30FT Rigid Header

-large pipe batt reel, several arms bent -left snout bent -wobble box seems very good, arm looks almost new -cast wobble box stand -bolt on sickle sections -auger has small weld & crack at hand hole, fingers look ok -small hole in bottom -rock guards -R.H. end shield, no left shield -no reel drive shield -back rail straight -drive shafts look ok

N Srs 3 24FT Rigid Header

-large pipe batt reel, wood sticks, 1 batt spliced, 1 batt repaired, 1 cracked -almost new 1344225 wobble box, stand welded -bolt on sickle sections -hydraulic reel lift & drive -black auger, large fingers, wide spaced flighting -bottom looks good -R.H. crop divider -R.H. shield, no left shield -self contained hydraulics -rock guards

N Srs 2 24FT Flex Header

-Nice black pickup reel, boards with metal teeth, rings & rollers all are in good condition. -wobble box -bolt on sickle sections -Flex parts look ok. -No end snouts, there is a rod on the left side and a small snout & rod on the right side. -Decent black auger, needs some finger guides and has some dings. -bottom probable ok -self contained hydraulics -hydraulic variable speed reel drive -hydraulic reel lift

900 Series 30FT Rigid Header

-batt reel with Anti-wrap ends (poor condition), 1 end batt is broken -spiral style auger fingers (good fingers), some flighting dinged a little, dented on L.H. end -bottom has some small repairs -bolt on, open style, sickle sections -hydraulic reel drive & lift -hydraulic fore & aft -good wobble box with weighted arm on a cast stand -end snouts decent -end shields -shaft hangers on combine end, need to be replaced -safety and field lights -rock guards

300 24FT Rigid Header AGCO

Hydraulics is run from combine hydraulic system. ********************** - Wobble box has some play., - front snouts & dividers, good, right hand reinforced, - no reel drive shield, - all metal batt reel with Anti-wrap ends, - grey auger - looks good, large fingers, - center throat torched open on side panels, - Hydraulics runs from combine, probably was converted., - bolt on sickle sections, - bottom looks good, - rock guards, - cutter bar looks ok

300 20FT Flex Header Deutz-Allis

Hydraulics is converted to run from combine hydraulic system. ********************** - metal pickup reel with plastic teeth, cut short, - bolt on sickle sections, - long flex snouts, - L.H. tin belt pulley is bad., - L.H. chain is bad., - end shields, - good wobble box, - hydraulic reel drive, - hydraulic reel lift, - black auger, large fingers, some dings, - dent in bottom, - front flex pan added to in center, - Was on R-62 - left drive shaft, hydraulic & electric hook ups,

218 18FT Rigid Header

-batt reel, small pipe, yellow batts -wobble box seems good -bolt on sickle sections -sickle head, loose -cutter bar seems good -bottom has worn areas -fingers hit some spots -hydraulic reel lift & drive -end shields -no rock guards

810 30FT Rigid Header

-Batt reel with large pipe -Anti-wrap ends -wobble box probably ok -Bolt to attach sickle is loose. -sickle, broken -bottom has several large patches installed nicely, useable as is -auger needs some guides -hydraulic reel lift & drive -rock guards -2 shaft couplers -back tin cracked at bolt holes, some welding -paint faded -no shields

900 Series 15FT Flex Header

-metal tear drop pick-up reel with plastic teeth -long flex snouts, right one bent on back -wobble box seems good -open style. bolt on sickle sections -sickle & guards look good -end shields -bottom looks ok -auger has a couple fingers missing -fingers have punched quite a few holes in at least 3 areas -auger has some dents -depth sensor & gauge

ROW HEAD

-decent tin work & snouts -decent gears & under side -belts weathered, usable -right hood, dented -right shield, missing; left shield, missing -skid shoes with almost new poly skids -gears look good -no stalk stompers -regular length drive shafts -auger looks good -small hole in bottom right seam of center -depth gauge

200 Series 24FT Rigid Header

-batt reel with Anti-wrap ends, some batts cracked -wobble box seems ok, but leaks (appears oily) -auger has center flighting extensions, needs some finger guides; left center weld, rewelded -sickle is mostly riveted -bottom looks ok -hydraulic reel drive & lift -late throat -rock guards -reel drive shield -no end shields

-Gleaner 830A LM Corn Head -Black -snouts, off, look ok -snap rolls worn -chain & sprockets, fair -auger, ok -bottom, hole on left side -right fender, small crack on top, a gash on the inside front and a dent in back -left fender, small dent in back -chain covers, fair

200 20FT Rigid Header

-early batt reel, yellow -good wobble box -bolt on sickle sections -guards look almost new -end shields, no reel end shield -good auger -bottom looks ok, 1 patch -no rock guards -throat post set in for no reverser -handles along back rail

Quik-tatch 16FT Rigid Header

-pickup reel, center pipe reinforced on left end -yellow riveted sickle sections -several newer guards -auger looks ok -bottom has holes -no rock guards -right divider bent a little -right reel arm reinforced -hydraulic reel lift -hydraulic reel drive -Hesston head hunter brackets -left end plate cracked & welded at back bolt

810 20FT Rigid Header

-wood with metal teeth black pickup reel with Anti-wrap ends -rock guards -wobble box looks good -riveted sickle, looks good -cutter bar looks good -auger has been opened & welded closed on right end -needs guide for 1 finger -center has a welded spot on auger -back panel rusty -bottom looks ok -hydraulic reel drive & lift -R.H. reel shield

N Srs 3 27FT Rigid Header

-Batt Reel large pipe wood sticks -rock guards -self contained hyd. -large finger auger -wobble box good -bolt on sickle sections -bottom good -LH Shield missing

SRS2 converted SRS 3

-was series 2, converted to series 3 -good snouts and tin -good auger -chains, snap rolls, & plates look ok -patched bottom -gears look ok -corn savers across back rail

200 20FT Flex Header

-Pick-up reel bent batt -Wobble box good -Sickle late. bolt on sections -Ball joint loose -Auger some fingers missing usable -Center flighting torched off -Bottom ok -Snouts long. left one bent -Shields right one gone -Left end welded on top front

PTO 540

Engine - stuck LP - PTO 540 - 3 Point no top link - Drawbar bent - Front axle adjustable. welded - Power steering

900 Series 30FT Rigid Header

-Good usable header -counterweighted wobble box -good sickle -auger is decent, has a couple dents, a few bad finger guides -batt reel, wavy, repaired in several places -reel lift cylinders look new -bottom is ok, but worn and thin -manual fore/aft

-runs & drives -hours unknown -18.4-34 rear tires, LH Firestone all traction field & road, RH unsure of brand, both weathered & cracked -7.50-15 front tires, LH Firestone 90%, RH Goodyear 75% -540 pto -3 point -swinging drawbar -front axle looks ok, tie rod bent

Running gear trailer

tongue repaired, bent and broken 6 bolt hubs 4 wheel: front tires very poor and cracked, rear tires ok modified running gear

Harvest Services Air Foil

Was last used about 2 years ago, it was ok when parked. Snouts look decent, some need new poly points, one is cracked. corn ear savers -Right fender is bent on top. -Chains, snap rolls, plates all look ok. -Auger has center flaps. -Bottom looks ok. -Drive shafts look ok. -Paint is decent. -no safety lights

3 point

-Snouts are in fair - good condition. -Right fender is welded. -Snap rolls are hard faced. -Stripper plates look fairly new. -corn savers have rust holes. -Auger looks ok. -Chains & sprockets look decent. -Bottom looks ok. -Throat is cut out for reverser -pin style connectors -side shields in place -Drive shafts have been extended & have support brackets - probably was adapted to different machine.

Row crop header # 9234 came with this trailer.

-single axle -5 bolt hubs, stud broken off, nuts missing -15" tires -flex bar

Running gear trailer

-4 wheel running gear trailer -single pipe with header supports -clevis type tongue hitch -5 bolt wheels & hubs -15" tires -one tire ok, P225/70 R15 -Other tires - G 78 x 15 are bad.

- Runs & drives ok, starts hard, starter might drag. - Fuel Solenoid was stuck, so it was removed; have to shut it off in the back. - 6343 hours on meter - Cab roof foam is gone, seat fair, radio, grain loss monitor & shaft monitor. - Feeder house is welded on the sides toward the front & middle. - Axle extensions - decent unloading tube with extension - adjustable rear axle with Firestone 14.9 x 24 S.A.T. II 23 deg. tires - 30.5 x 32 Firestone S.A.T. 23 deg. 12 ply stubble cut front tires - corn chaffer - decent rotary deflector - decent straw spreader - good tin work

-Push bar is good. -batt-tine tooth reel -riveted sickle sections -Auger has spring tooth center, and 2 small holes on left of center. -Bottom looks ok. -left end welded -One rubber crimper roller & one skeleton type crimper roller -sickle drive fly wheel

-Nice black large pipe bat reel -bolt on sickle sections -Wobble box seems ok. -end shield, bent -Bottom has some holes at right & left center throat -spiral fingered auger, shiny, looks recently used -rock guards -back shafts seem ok -field lights -Tin work looks repainted & peeling. -8820 bumps by throat (inside)

2 Wheel

-2" ball hitch -jack stand, no jack -single axle with 205/70 R 15 tire on 5 bolt rim on right hand side -ST 205/75 R 14 tire on 5 bolt rim on left hand side -4 header supports, no flex bar -2 frame supports

-metal batt reel, wood sticks, anti wrap ends -Left hand end is reinforced at wobble box, and one block is missing. -riveted sickle, good -black auger, reinforced center -some milo guards -rock guards, reinforced to back of header -hydraulic reel lift -variable speed reel -good back shafts -Shields are missing.

-Batt reel has Anti-wrap ends. -manual variable speed reel -hydraulic reel lift -twin wobble boxes -left reel shield -Wobble box end shields are gone. -bolt on sickle sections -flex drive shafts -decent auger, center flap welded on -bottom, decent -rock guards

4 Wheel, had 810 Case/IH Header

-Two inch ball hitch -jack -two axles -15 inch tires

with rear loader

-has tree sheer attachment on a loader -seat turned around to use backwards -spray attachment on front -gas engine -13.6 x 28 P.A. rims -adjustable front axle -6.50 x 15 front tires on 5 bolt rims -540 PTO -drawbar front & back -hydraulic & power steering appear to run from front mounted pump -hitch for rear arms

-Batt reel -black auger, small finger -L.H end welded -decent pitman & bell crank -riveted sickle -good bottom -rock guards -some shields

-wood batt reel, poor condition -decent cutter bar & sickle -auger ok -bottom has some holes -no hydraulics

-batt reel, large pipe -drive motor missing -wobble box seems ok -decent sickle and cutter bar -side & reel shields -good auger -bottom looks decent -rock guards -looks shedded

- metal batt reel, wood sticks & some home make angle iron, - left reinforced, - black auger, small fingers, small dents, - bolt on sickle sections, - rock guards, - v.s. area burned, - reel shield, - cutter bar looks ok, - end hoops, - needs 1 chain idler, - one piece pitman, - bell crank, tight

-wood board style, black pickup reel -bottom, usable but loose at throat -auger appears to have the center replaced -front flex plates need to be adjusted & re-attached -left side drive is a flex shaft -right side shaft is standard -I.H. wobble box -long flex snouts, right one is off -hydraulic reel lift

-left fender & snout bent -1 Center snout dented the rest ok -good snap rolls -good chains -some rows repaired where corn comes into auger -RH row frame welded -poly Bottom -Auger ok - flighting worn some -Flex Drive shafts -2 gear boxes a little oily -leaf shield on back rail

300 20FT Flex Header AGCO

*********Hydraulics on Header********** -Header has small amount of collision damage. -Front center plate popped up, other damage unknown. -Pickup Reel -black round pipe PU Reel w/ plastic fingers most have been cut short -decent sickle -decent bottom -sickle bolt to connect to wobble box gone -flex snout on left side damaged right side also -gray auger big finger -self contained hyd. -Hydraulic reel lift

Wide Adj front Axle

540 PTO - front shaft was close to fire, but ok 7 foot dual rear tires Gearbox is clean. Blades are decent.

Probably used 4 years ago. tear drop style pick up reel with paddle fingers Wobble box seems ok. fine cut sickle Auger has poly fingers, a few small dents, seems ok overall. no end shields no holes or patches in floor

200 hours on roter gearboxes used about 4 years ago runs & drives ok decent cab & seat bin fill auger & tube worn, poly liner also thin left hand front tire - Titan 24.5 x 32, 70%, 12 ply no cracks right hand front tire - Firestone 24.5 x 32, 60%, 12 ply no cracks right hand rear tire - Titan 12.4 x 24, 80%, 8 ply no cracks left hand rear tire Cambridge, 12.4 x 24, 30% 8 ply poor condition chaff/straw spreader right hand shield off but with machine Ford engine lateral tilt feeder house feeder chain broken & bent feeder drum dented small grain chaffer Unloading tube looks good. Auger is sharp & worn.