dual drive
both end shields in place
oil bath wobble box
sickle, good
guards, good
full finger auger, center flighting extensions
pickup reel, ok, some bushing pipes repaired
bottom ok
combine hookup hoses missing
LH drive
open style wobble box
end shields missing
manual fore & aft
auger, ok
early style pickup reel, some sections bent
bottom, decent
sickle, decent
guards, decent
-Hydraulic hoses that connect to the combine are missing.
-Challenger yellow shield
-safety lights - wires disconnected
-Black pipe pick up reel with poly teeth and solid Anti-wrap ends
-hydraulic reel drive & lift
-electric hydraulic Fore & aft
-long flex divider snouts
-open style wobble box
-bolt on sickle sections
-tall flighting, gray auger, big fingers & guides
-Bottom looks ok.
-Front stainless looks ok.
-1000 spline PTO, shaft drive left side
-poly skids on front flex plates
-decent paint
-Back rail is straight.
-wide throat hook up options
-Sat in shed for years and not used.
- metal batt reel
- hydraulic reel lift & drive
- hydraulic Fore & Aft
- bolt on sickle sections
- Auger needs finger guides & one finger, also has flighting extensions,
- Bottom looks ok.
- rock guards
- left PTO drive shaft
- shields
- open style wobble box
- crop dividers, right hand one home made
Hydraulics is run from combine hydraulic system. **********************
Pickup Reel - tear drop metal batt reel with poly teeth cut short
w/ good rings & open sided Anti-wrap ends
- hydraulic reel lift & drive
- long flex snouts
- wobble box drive
- bolt on sickle sections
- large finger auger
- Bottom looks ok.
- paint faded
- shields probably all there
- Hydraulics runs from combine system
-all metal tear drop style pickup reel, poly fingers
-hydraulic reel drive & lift
-Wobble box drives from both sides.
-good bolt on sickle sections, extra left hand sickle
-good looking guards
-Auger looks good.
-Bottom looks good.
-Most shields are in place.
-PTO drives on both sides
-rock guards
-reel drive, hoses poor
-crop dividers
-good paint
Hydraulics is run from combine hydraulic system.
**********************
- Batt reel, all metal with Anti-wrap ends,
- Auger is decent, flighting extensions in center, needs finger guides.,
- rock guards,
- single drive shaft,
- open wobble box,
- bolt on sickle sections,
- Head bolt is a little loose, should tighten ok.,
- Cutter bar looks decent.,
- Bottom looks ok.,
- Hydraulic reel lift & drive,
- Left crop divider rod is gone, right one is in place.,
- Left end shield is missing.,
- Left idler pulleys & belt look good.,
- Back rail is ok.,
- Black paint is faded.
Hydraulics is run from combine hydraulic system.
**************
- Header was on R62,
- pickup reel,
- poly skids,
- flex snouts,
- single drive shaft,
- hydraulic reel lift & drive,
- open wobble box,
- equipped with Gebr. Schumacher, easy cut cutter bar system S.I. Distributing, St. Marys, Ohio,
- bolt on sickle sections,
- Flex bar, pan & bottom look ok.,
- Big Finger auger,
- Shields are in place, green strip.
Black pickup reel with wood boards, decent reel
Rivited sickle sections.
Good wobble box, looks like it was recently replaced.
Bottom patched and some holes on left side
Auger looks ok.
Rock guards
hydraulic reel drive & lift
self contained hydraulics on right hand side
Black paint is poor.
-Large pipe black, batt reel
-Wobble box arm is broken & loose.
-bolt on sickle sections
-Guards & cutter bar look good.
-L.H. crop divider, snouts welded or dinged some
-good bottom
-Some of the rock guards are worn & dented in.
-Auger needs some finger guides, random style.
-end shields
-hydraulic reel lift, drive & fore & aft
-Drive shaft look good.
Bottom looks ok, small dings.
Auger looks ok, small dings.
Left hand PTO shaft drives the auger.
Hydraulic system drives the pick up unit.
Rake up Precision Metal Fabrication, LTD
- Rosetown, Saskatchewan - s/n 125-9114
- Draper belts have alluminum batts with rubber & poly teeth.
- One alluminum batt is broken. Batts are run by a drive box.
- Draper is run by a hydraulic motor, held with shock absorbers.
-Batt reel with Anti-wrap on one end
-wobble box, ok
-bolt on sickle sections, ball joint loose
-spiral finger auger
-bottom patched
-Left end shield is gone.
-rock guards
-Left hand end pulley is almost new.
-tine & batt type reel, 1 batt is off
-bolt on sickle sections
-Auger has some dents, center flap, looks usable
-Bottom looks decent.
-double sickle drives
-skid shoes
-center link
-warning lights broken off.
-Left end is rusty.
-Left back rail drive shaft support is welded.
Batt reel with Anti-wrap ends, batts are bent & welded.
rock guards
hydraulic reel drive & lift
Hydraulic Fore & Aft
Wobble box feels good.
bolt on sickle sections, look good
Bottom looks ok.
Auger looks ok.
PTO drive shafts, both sides
Right side has shields, left side shield is missing.
-Pickup reel has wood boards, metal teeth, drain pipes over wood rings & rollers (look ok), Anti-wrap ends.
-Black open style wobble box
-tiger teeth sickle and guards, bolt on sections
-Flex bar & snouts, left snout is welded.
-Variable speed reel
-Hydraulic reel lift; master cylinder is a little oily.
-Black auger has small fingers & neoprene guides.
-Bottom is patched, but usable.
-Depth control gauge looks disconnected.
-Hydraulic hoses to combine are missing.
-drive coupler
-Batt reel with Anti-wrap ends, batts are wavey.
-hydraulic reel drive & lift
-good wobble box on cast stand
-bolt on sickle sections
-left snout bent a little
-Bottom has center patch
-Left shield is missing. Tear drop shield for reel drive is missing.
-Auger is good, nice center repair kit, spiral finger pattern
-rock guards
Hydraulics is run from combine hydraulic system.
**********************
- black metal tear drop pickup reel with plastic teeth,
- bolt on sickle sections,
- Cutter bar looks ok.,
- open wobble box,
- hydraulic reel lift,
- Bottom has one large hole left of center, otherwise it looks ok.,
- Left hand end shield is missing.,
- one weld crack on lift side on back rail,
- Back shaft is ok.,
- 3 right side weights,
- crop dividers,
- large finger auger
-(178 W) 14' Head is from JD 830.
-Steel conditioners look good.
-wobble box
-bolt on sickle sections
-Yellow batt / pickup reel looks ok.
-Push bar is straight.
-small dents in auger, center flaps
-Bottom is probable ok.
-weld at crimper attach bracket
-skid shoes
-large pipe batt reel, several arms bent
-left snout bent
-wobble box seems very good, arm looks almost new
-cast wobble box stand
-bolt on sickle sections
-auger has small weld & crack at hand hole, fingers look ok
-small hole in bottom
-rock guards
-R.H. end shield, no left shield
-no reel drive shield
-back rail straight
-drive shafts look ok
-Nice black pickup reel, boards with metal teeth, rings & rollers all are in good condition.
-wobble box
-bolt on sickle sections
-Flex parts look ok.
-No end snouts, there is a rod on the left side and a small snout & rod on the right side.
-Decent black auger, needs some finger guides and has some dings.
-bottom probable ok
-self contained hydraulics
-hydraulic variable speed reel drive
-hydraulic reel lift
-batt reel with Anti-wrap ends (poor condition), 1 end batt is broken
-spiral style auger fingers (good fingers), some flighting dinged a little, dented on L.H. end
-bottom has some small repairs
-bolt on, open style, sickle sections
-hydraulic reel drive & lift
-hydraulic fore & aft
-good wobble box with weighted arm on a cast stand
-end snouts decent
-end shields
-shaft hangers on combine end, need to be replaced
-safety and field lights
-rock guards
Hydraulics is run from combine hydraulic system.
**********************
- Wobble box has some play.,
- front snouts & dividers, good, right hand reinforced,
- no reel drive shield,
- all metal batt reel with Anti-wrap ends,
- grey auger - looks good, large fingers,
- center throat torched open on side panels,
- Hydraulics runs from combine, probably was converted.,
- bolt on sickle sections,
- bottom looks good,
- rock guards,
- cutter bar looks ok
Hydraulics is converted to run from combine hydraulic system.
**********************
- metal pickup reel with plastic teeth, cut short,
- bolt on sickle sections,
- long flex snouts,
- L.H. tin belt pulley is bad.,
- L.H. chain is bad.,
- end shields,
- good wobble box,
- hydraulic reel drive,
- hydraulic reel lift,
- black auger, large fingers, some dings,
- dent in bottom,
- front flex pan added to in center,
- Was on R-62
- left drive shaft, hydraulic & electric hook ups,
-batt reel, small pipe, yellow batts
-wobble box seems good
-bolt on sickle sections
-sickle head, loose
-cutter bar seems good
-bottom has worn areas
-fingers hit some spots
-hydraulic reel lift & drive
-end shields
-no rock guards
-Batt reel with large pipe
-Anti-wrap ends
-wobble box probably ok
-Bolt to attach sickle is loose.
-sickle, broken
-bottom has several large patches installed nicely, useable as is
-auger needs some guides
-hydraulic reel lift & drive
-rock guards
-2 shaft couplers
-back tin cracked at bolt holes, some welding
-paint faded
-no shields
-metal tear drop pick-up reel with plastic teeth
-long flex snouts, right one bent on back
-wobble box seems good
-open style. bolt on sickle sections
-sickle & guards look good
-end shields
-bottom looks ok
-auger has a couple fingers missing
-fingers have punched quite a few holes in at least 3 areas
-auger has some dents
-depth sensor & gauge
-batt reel with Anti-wrap ends, some batts cracked
-wobble box seems ok, but leaks (appears oily)
-auger has center flighting extensions, needs some finger guides; left center weld, rewelded
-sickle is mostly riveted
-bottom looks ok
-hydraulic reel drive & lift
-late throat
-rock guards
-reel drive shield
-no end shields
-early batt reel, yellow
-good wobble box
-bolt on sickle sections
-guards look almost new
-end shields, no reel end shield
-good auger
-bottom looks ok, 1 patch
-no rock guards
-throat post set in for no reverser
-handles along back rail
-pickup reel, center pipe reinforced on left end
-yellow riveted sickle sections
-several newer guards
-auger looks ok
-bottom has holes
-no rock guards
-right divider bent a little
-right reel arm reinforced
-hydraulic reel lift
-hydraulic reel drive
-Hesston head hunter brackets
-left end plate cracked & welded at back bolt
-wood with metal teeth black pickup reel with Anti-wrap ends
-rock guards
-wobble box looks good
-riveted sickle, looks good
-cutter bar looks good
-auger has been opened & welded closed on right end
-needs guide for 1 finger
-center has a welded spot on auger
-back panel rusty
-bottom looks ok
-hydraulic reel drive & lift
-R.H. reel shield
-was series 2, converted to series 3
-good snouts and tin
-good auger
-chains, snap rolls, & plates look ok
-patched bottom
-gears look ok
-corn savers across back rail
-Pick-up reel bent batt
-Wobble box good
-Sickle late. bolt on sections
-Ball joint loose
-Auger some fingers missing usable
-Center flighting torched off
-Bottom ok
-Snouts long. left one bent
-Shields right one gone
-Left end welded on top front
-Good usable header
-counterweighted wobble box
-good sickle
-auger is decent, has a couple dents, a few bad finger guides
-batt reel, wavy, repaired in several places
-reel lift cylinders look new
-bottom is ok, but worn and thin
-manual fore/aft
-runs & drives
-hours unknown
-18.4-34 rear tires, LH Firestone all traction field & road, RH unsure of brand, both weathered & cracked
-7.50-15 front tires, LH Firestone 90%, RH Goodyear 75%
-540 pto
-3 point
-swinging drawbar
-front axle looks ok, tie rod bent
-Snouts are in fair - good condition.
-Right fender is welded.
-Snap rolls are hard faced.
-Stripper plates look fairly new.
-corn savers have rust holes.
-Auger looks ok.
-Chains & sprockets look decent.
-Bottom looks ok.
-Throat is cut out for reverser
-pin style connectors
-side shields in place
-Drive shafts have been extended & have support brackets - probably was adapted to different machine.
